Skip to content. | Skip to navigation

Personal tools

You are here: Home

Search results

RSS Subscribe to an always-updated RSS feed.

3079 items matching your search terms.
Filter the results.
Item type



































New items since



Sort by relevance · date (newest first) · alphabetically
Article Reference Physiological response to seawater pH of the bivalve Abra alba, a benthic ecosystem engineer, is modulated by low pH
Located in Library / RBINS Staff Publications 2022 OA
Article Reference Climate change effects on the ecophysiology and ecological functioning of an offshore wind farm artificial hard substrate community
Located in Library / RBINS Staff Publications 2022 OA
Article Reference A new small, mesorostrine inioid (Cetacea, Odontoceti, Delphinida) from four upper Miocene localities in the Pisco Basin, Peru
Located in Library / RBINS Staff Publications 2020
Article Reference Toward a Harmonization for Using in situ Nutrient Sensors in the Marine Environment
Improved comparability of nutrient concentrations in seawater is required to enhance the quality and utility of measurements reported to global databases. Significant progress has been made over recent decades in improving the analysis and data quality for traditional laboratory measurements of nutrients. Similar efforts are required to establish high-quality data outputs from in situ nutrient sensors, which are rapidly becoming integral components of ocean observing systems. This paper suggests using the good practices routine established for laboratory reference methods to propose a harmonized set of deployment protocols and of quality control procedures for nutrient measurements obtained from in situ sensors. These procedures are intended to establish a framework to standardize the technical and analytical controls carried out on the three main types of in situ nutrient sensors currently available (wet chemical analyzers, ultraviolet optical sensors, electrochemical sensors) for their deployments on all kinds of platform. The routine reference controls that can be applied to the sensors are listed for each step of sensor use: initial qualification under controlled conditions in the laboratory, preparation of the sensor before deployment, field deployment and finally the sensor recovery. The fundamental principles applied to the laboratory reference method are then reviewed in terms of the calibration protocol, instrumental interferences, environmental interferences, external controls, and method performance assessment. Data corrections (linearity, sensitivity, drifts, interferences and outliers) are finally identified along with the concepts and calculations for qualification for both real time and time delayed data. This paper emphasizes the necessity of future collaborations between research groups, reference-accredited laboratories, and technology developers, to maintain comparability of the concentrations reported for the various nutrient parameters measured by in situ sensors.
Located in Library / RBINS Staff Publications 2020
Article Reference The initial response of females towards congeneric males matches the propensity to hybridise in Ophthalmotilapia
Located in Library / RBINS Staff Publications 2022 OA
Article Reference D source code Handbook of best practice and standards for 2D+ and 3D imaging of natural history collections
Located in Library / RBINS Staff Publications 2020
Article Reference Global realized niche divergence in the African clawed frog Xenopus laevis
Located in Library / RBINS Staff Publications 2017
Article Reference The genus Diplommatina Benson, 1849 (Gastropoda: Caenogastropoda: Diplommatinidae) in Nepal, with the description of seven new species
Located in Library / RBINS Staff Publications 2017
Article Reference The complexity of 3D stress-state changes during compressional tectonic inversion at the onset of orogeny
Compressional tectonic inversions are classically represented in 2D brittle failure mode (BFM) plots that illustrate the change in differential stress (σ1−σ3) versus the pore-fluid pressure during orogenic shortening. In these BFM plots, the tectonic switch between extension and compression occurs at a differential stress state of zero. However, mostly anisotropic conditions are present in the Earth's crust, making isotropic stress conditions highly questionable. In this study, theoretical 3D stress-state reconstructions are proposed to illustrate the complexity of triaxial stress transitions during compressional inversion of Andersonian stress regimes. These reconstructions are based on successive late burial and early tectonic quartz veins which reflect early Variscan tectonic inversion in the Rhenohercynian foreland fold-and-thrust belt (High-Ardenne Slate Belt, Belgium, Germany). This theoretical exercise predicts that, no matter the geometry of the basin or the orientation of shortening, a transitional ‘wrench’ tectonic regime should always occur between extension and compression. To date, this intermediate regime has never been observed in structures in a shortened basin affected by tectonic inversion. Our study implies that stress transitions are therefore more complex than classically represented in 2D. Ideally, a transitional ‘wrench’ regime should be implemented in BFM plots at the switch between the extensional and compressional regimes.
Located in Library / No RBINS Staff publications
Article Reference Stress-state evolution of the brittle upper crust during compressional tectonic inversion as defined by successive quartz vein types (High-Ardenne slate belt, Germany)
In the frontal part of the Rhenohercynian fold-and-thrust belt (High-Ardenne slate belt, Germany), two successive types of quartz veins, oriented normal and parallel to bedding respectively, are interpreted to reflect the early Variscan compressional tectonic inversion of the Ardenne–Eifel sedimentary basin. Fracturing and sealing occurred in Lower Devonian siliciclastic multilayers under very low-grade metamorphic conditions in a brittle upper crust. A geometrical and microthermometric analysis of these veins has helped to constrain the kinematic and pressure–temperature conditions of both vein types, allowing the reconstruction of the stress-state evolution in a basin during tectonic inversion. It is demonstrated that bedding-normal extension veins, which developed under low differential stresses and repeatedly opened and sealed (crack-seal) under near-lithostatic fluid pressures, reflect the latest stage of an extensional stress regime. Bedding-parallel veins, which developed at differential stresses that were still low enough to allow the formation of extension veins, cross-cut the bedding-normal veins and preceded the regional fold and cleavage development. These veins show a pronounced bedding-parallel fabric, reflecting bedding-normal uplift and bedding-parallel shearing under lithostatic to supra-lithostatic fluid pressures during the early stages of a compressional stress regime. This kinematic history corroborates that fluid overpressures are easy to maintain during compressional tectonic inversion at the onset of orogeny.
Located in Library / No RBINS Staff publications